Eliminate Dell Error Code 2000-0146 With Effective Hacks

Windows users often encounter the error code 2000-0146 when there are any problems with the hard drive and not booting the OS. As a result, the hard drive fails to start by itself and restricts from operating.

This is a common situation and there are several reasons why it might happen. This issue not only happens with the old hard drives, but it can also happen with a newly purchased hard drive as well.

If you also face the same problem, then nothing to get worried about this. Here in this guide, you will know some amazing hacks which can help you to fix this error. Hence, you are advised to go through the article given below. So, let’s start.  

Why does the Dell Error Code 2000-0146 Occur?

Usually, Dell error code 2000-0146 occurs due to the hard drive problems of the system. It may have bad fragments/sector or it might be damaged physically. If the error is not appearing due to the software, then there might be some physical problems as well.

Have a look at the other reasons pointed below:

  • You can face this error due to the AHCI or IDE of the SATA Mode. They might be clashing with the hard disk.  
  • If the SATA cable is not working, then you can encounter this error.
  • Sometimes, the Basic Input Output System can cause this issue.
  • If other physical components of the system (such as RAM) get damaged, then you can also come across this error.

Now, you are aware of the common causes of this error. Match the above points with your current situations and identify the specific cause. Now, you just need some hacks to troubleshoot this error.

Easy Hacks to Fix Dell Error Codes 2000-0146

There are a lot of ways to fix this error. Hence, you should stick to the steps given below to get the most fruitful results:

Procedure 1: Change the SATA Mode

To determine the communicating process between the hard drive and the system is the principal job of SATA modes. IDE is the simplest mode where the hard disk is set to run as a parallel ATA whereas AHCI or (Advanced Host Controller Interface) provides advanced functions (such as hot swapping) to be performed.

Hence, you can try to modify the SATA mode to check if can help you to detect the hard drive. To perform this, you should have a look at the steps mentioned below:

  1. First, you have to enter the BIOS. Then, hit the F1, F2, F3, etc keys from the keyboard to input the BIOS.
  2. It will open the Settings of the Basic Input Output System. Now, you should navigate to the ‘Storage Configuration’ section.
  3. Modify the settings between AHCI and IDE. If you see that it is set to IDE, then you should change it to AHCI.  
  4. After completing the above steps, you have to restart the system to apply the changes.

Now, check whether the error has been resolved or not. If the error persists, then you should move on to further solutions.

Procedure 2: Check the Hard Drive for any Bad Fragments/Sectors

After changing the SATA mode, if you see that the error code still appears, then you can change it to default. After that, you have to check the hard drive of the system if there exist any bad fragments or sectors. Perform the steps given below to check the hard disk:

  1. At first, you have to restart the system. Then, hit the F11 key from the keyboard to navigate to the ‘Recovery Environment’ category. Now, choose the ‘Troubleshoot’ option from the list.
  2. Now, move the cursor to the upper left side o the window and tap on the Advanced tab. Then, choose the ‘Command Prompt’ option from the list.
  3. As a result, it will open the Command Prompt window with the administrator privileges. Then, type the commands given below and hit the Enter key from the keyboard to execute the command.

1st: chkdsk C: /r /x

2nd: chkdsk C: /

Here you have to change the ‘C’ with your drive.

  1. Now, you have to wait for a few time until the ‘chkdsk’ process running. It will take a minimum of 14-16 hours of time to complete the process.
  2. Once the ‘chkdsk’ process completes, you have to restart the system to apply the changes.

After that, you have to check whether the error still persists or not. If you see that the error is still continuing, move to the next one.

Procedure 3: Run a Full System Scan

If your hard drive is affected by virus or malware, then you can also face the error. Hence, you can try to scan the system to fix this error.  

How do You Run a System Scan?

  1. First, move the cursor to the left bottom corner of the screen and tap on the Start logo.
  2. Then, type ‘defender’ on the search bar and click twice on the Windows Defender to open the tool.
  3. Navigate to the left pane of the screen and tap on the Shield icon.
  4. On the next window, tap on the ‘Advanced Scan’ option.
  5. Choose the ‘Full Scan’ option from the current window and open a full system malware scan.
  6. Now, it will start to scan the entire system for the virus or malware. Wait for a few time and remove all the virus from the system. Tap on the ‘Clean’ button to eliminate the virus or malware from the system.
  7. Next, restart the system and apply the changes.

After that, you should check if the error code still appears or not. If the error still occurs, then go to the next method. Moreover, if you are struggling to complete the procedure successfully, then talk to an expert for exact guidance.

Procedure 4: Run Disk Checkup

You can also fix this error by running the disk checkup. Disk Checkup is an in-built tool of Windows Operating System that helps the users by eliminating the unnecessary files of the hard drive.

It also removes the temporary files, unwanted system files of the system. It might be responsible for showing the Dell error code 2000-0146. To run the Disk Checkup tool, you should perform the steps as follows:  

  1. Navigate to the Start menu.
  2. Then, type ‘Disk Cleanup’ in the search bar and hit the Enter key from the keyboard o navigate to the Disk Cleanup window.
  3. As a result, it will start to scan the hard drive.  
  4. After finishing the scanning procedure, you should tick the ‘Temporary files’ box. Then, click on the OK button.
  5. No, tap on the ‘Delete files’ option to remove the temporary files of the system.

After that, close the current window and restart the system. Then, you should check whether the error code still appears or not. If the error code is still unresolved, then you should perform procedure 5.

Procedure 5: Repair the PC Registry

Due to the corrupted registry files, you can also face this issue. To repair the registry files of the system, you should use Microsoft’s in-built tool SFC. This tool verifies the integrity of the system files as well as repair them by itself.

How do You Repair the Registry Files of the System?

  1. First, you have to launch the Start menu.
  2. Then, type ‘cmd’ in the search bar of the Start menu.
  3. Right-click on the ‘Command Prompt’ option and choose the ‘Run as Administrator’ option from the list to run the Command Prompt with administrator privileges.
  4. Now, type ‘sfc/scannow’ in the ‘Command Prompt’ window and hit the Enter key from the keyboard to run the command.
  5. Now, it will start the scanning process. Once it locates the corrupted registry files, it will fix them automatically.
  6. Close the current window and restart the system to apply the changes.

Procedure 6: Run PSA Diagnostics

You can also fix this particular error by running the PSA diagnostics. PSA diagnostic is an in-built tool of Windows Operating System that can help you to fix this issue. To run this, follow the steps mentioned below:

  1. Hit the F12 key and hold it until the Dell logo and ‘One Time Boot’ menu appears.
  2. Navigate to the ‘PSA Diagnostics’ option and hit the Enter key from the keyboard.
  3. Now, the PSA starts to run automatically. Perform the on-screen guidance to solve this error.

After that, restart the system and check whether the error is resolved.

Final Recommendation…

In the above post, we have explained some of the easiest solutions to fix Dell error code 2000-0146. It is our hope that if you perform the above methods in their respective order, then it will definitely help you to put an end to this bug.

If you are still unable to fix the error after performing the above ways, or if you are facing any types of trouble while implementing the above ways, then you should contact a tech expert. Any professional who is well experienced in this field can help you to fix Dell error codes without much hassle. Additionally, you can also share your queries and valuable feedback through the comment box given at the end of this post.

Leave a Comment

Your email address will not be published.

fifty eight ÷ fifty eight =

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>

Call Our Technical Support Phone Number for DELL ? @ USA : +1-800-354-8923, UK: +44-800-086-9078, AUS: +61-180-071-7665 Right Now to Get Instant Help

Send a Message
Dell customer support numbers 4.2 out of 5 based on 5 reviews as of March 2018. -